Co-author Network
Co-researcher Network
sample of publications
-
articles
- Drilling of Cross-Ply UHMWPE Laminates: A Study on the Effects of the Tool Geometry and Cutting Parameters on the Integrity of Components. Polymers. 15:1-21. 2023
- Machinability of 3D printed peek reinforced with short carbon fiber. Composites Part C: Open Access. 12, 100387:1-10. 2023
- 'FLIPPED ASSESSMENT': Proposal for a Self-Assessment Method to Improve Learning in the Field of Manufacturing Technologies. Education Sciences. 13:1-15. 2023
- Microstructure Effects on the Machinability of AM-Produced Superalloys. Crystals. 13:1-16. 2023
- Influence of machining parameters on fretting fatigue life of Inconel 718. International Journal of Fatigue. 162:1-12. 2022
- High-pressure cooling in finishing turning of haynes 282 using carbide tools: Haynes 282 and inconel 718 comparison. Metals. 11:1-20. 2021
- Drilling of biocomposite materials: Modelling and experimental validation. SIMULATION MODELLING PRACTICE AND THEORY. 106:1-15. 2021
- Machinability of INCONEL718 Alloy with a Porous Microstructure Produced by Laser Melting Powder Bed Fusion at Higher Energy Densities. Materials. 13. 2020
- Energy absorption and residual bending behavior of biocomposites bumper beams. Composite structures. 245:1-7. 2020
- Postmortem analysis using different sensors and technologies on aramid composites samples after ballistic impact. SENSORS. 20:1-16. 2020
- Analysis of orthogonal cutting of biocomposites. Composite structures. 234:1-14. 2020
- Multi-objective optimization analysis of cutting parameters when drilling composite materials with special geometry drills. Composite structures. 225. 2019
- Sustainable high-speed finishing turning of haynes 282 using carbide tools in dry conditions. Metals. 9:1-14. 2019
- Analysis of the Machinability of Carbon Fiber Composite Materials in Function of Tool Wear and Cutting Parameters Using the Artificial Neural Network Approach. Materials. 12:1-13. 2019
- Experimental and Numerical Analysis of Conical Projectile Impact on Inconel 718 Plates. Metals. 9:1-12. 2019
- Experimental and numerical analysis of the influence of drill point angle when drilling biocomposites. Composite structures. 209:700-709. 2019
- Experimental analysis for stabbing resistance of different aramid composite architectures. Composite structures. 208:525-534. 2019
- Experimental analysis of drilling induced damage in biocomposites. TEXTILE RESEARCH JOURNAL. 88:2544-2558. 2018
- Finishing turning of Ni superalloy Haynes 282. Metals. 8:1-12. 2018
- Experimental analysis of drilling induced damage in aramid composites. Composite structures. 202:1136-1144. 2018
- Experimental analysis of special tool geometries when drilling woven and multidirectional CFRPs. JOURNAL OF REINFORCED PLASTICS AND COMPOSITES. 35:33-55. 2016
- Manufacture of compression moulded PLA based biocomposites: A parametric study. Composite structures. 131:995-1000. 2015
- Experimental analysis of the influence of drill point angle and wear on the drilling of woven CFRPs. Materials. 7:4258-4271. 2014
-
book chapters
-
conference contributions
- Machinability characterization of 3D printed PEEK 2023
- Material characterization of basalt and carbon laminates with and without open-hole under static and fatigue loads 2023
- Analysis of machining performance of Inconel 718 printed by PBF-LM (powder bed fusion laser melting). 2021
- Educational Resources for Self-learning of Descriptive Geometry. 186-194. 2019
- Análisis del taladrado de material compuesto 100% biodegradable. 390-398. 2018
- Influence of the undeformed chip cross section in finishing turning of Inconel 718 with PCBN tools. 122-125. 2018
- Impact and Compression after Impact (CAI) behavior of PLA/Flax biocomposites. 111-111. 2016
- Modeling of viscoelastoplastic behavior of Flax/PLA biodegradable composites. 111-111. 2016
- Parametric study on the manufacturing of biocomposite materials. 243-254. 2016
- Simulation of the impact behavior of PLA/Flax biocomposites. 172-173. 2016
- A study of induced damage during drilling on natural fibre based biocomposites 2015
- Analysis of the manufacturing parameters on the mechanical properties of natural fibres composites 2015
- Estimation of thermal effects in dry drilling of Ti6Al4V. 433-439. 2015
- Numerical modelling of the thermal effects on material in drilling processes Ti6Al4V alloy. 427-432. 2015
- Numerical study of the behaviour of natural fibres composites under low-velocity impact 2015
- Implementation of a numerical model to define a bending manufacturing process. 36-41. 2014
- Influence of tool geometry in drilling of CFRP. 1-8. 2014
-
theses