sample of publications

• articles 

  • Microstructural, chemical, and mechanical characterization of extruded Al-Cu-Li rods.  MATERIALS CHARACTERIZATION.  203:1-14. 2023
  • Assessment of Plasma Deposition Parameters for DED Additive Manufacturing of AA2319.  Journal of Manufacturing and Materials Processing.  7:113-1-113-14. 2023
  • Wire Arc Additive Manufacturing (WAAM) for Aluminum-Lithium Alloys: A Review.  Materials.  16:1-20. 2023
  • Sliding wear behavior of intermetallic Ti-45Al-2Nb-2Mn-(at%)-0.8vol%TiB2 processed by centrifugal casting and hot isostatic pressure: Influence of microstructure.  Materials.  15:1-12. 2022
  • Relationship between Manufacturing and Properties of Vacuum Sintered Ti and Ti-6Al-7Nb.  Journal of Alloys and Compounds.  1:232-242. 2022
  • Effect of heat treatment prior to direct hot-extrusion processing of Al-Cu-Li alloy.  Metals.  12:1-15. 2022
  • Fast surface disinfection with COUNTERFOG® SDR-F05A+.  European Physical Journal Plus.  136:1-8. 2021
  • The effect of microstructure and strain rate on the 25 degrees C and 700 degrees C compression deformation behavior of powder metallurgy processed Ti-45Al-2Nb-2Mn (at.%)-0.8 TiB2 (vol%) alloy.  MATERIALS CHARACTERIZATION.  172:110856-110871. 2021
  • A comparison of field assisted hot pressing and hot isostatic pressing for gas atomized Ti-22Al-26Nb(at.%) and Ti-22Al-26Nb-5B(at.%) powders.  Journal of Alloys and Compounds.  852:156870-156884. 2021
  • Decontamination of Diesel particles from air by using the Counterfog (R) system.  Air Quality Atmosphere and Health.  12:305-310. 2019
  • Secondary Phases Quantification and Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds for High-Field Superconducting Magnets.  IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY.  28. 2018
  • Joint Effect of Steel Addition and Press-and-Sinter on the Properties of Low-Cost PM Ti Alloys.  Key Engineering Materials (Key Engineering Materials).  770:248-254. 2018
  • Magnetic and morphological characterization of Nd2Fe14B magnets with different quality grades at low temperature 5-300 K.  JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS.  451:549-553. 2018
  • A Comparative Study of Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds.  JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE.  27:1995-2002. 2018
  • Electrochemical comparative study on corrosion behavior of conventional and powder metallurgy titanium alloys in physiological conditions.  Metal Powder Report.  7:118-123. 2017
  • Evaluation of the mechanical properties of powder metallurgy Ti-6Al-7Nb alloy.  Journal of the Mechanical Behavior of Biomedical Materials.  67:110-116. 2017
  • Quantifying the properties of low-cost powder metallurgy titanium alloys.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  687:47-53. 2017
  • Understanding the properties of low-cost iron-containing powder metallurgy titanium alloys.  MATERIALS & DESIGN.  110:317-323. 2016
  • Performance of Magnetic-Superconductor Non-Contact Harmonic Drive for Cryogenic Space Applications.  Machines.  3:138-156. 2015
  • Feasibility study of the production of biomedical Ti&-6Al&-4V alloy by powder metallurgy.  Materials Science & Engineering C-Materials for Biological Applications.  49:400-407. 2015
  • Fabrication of a novel hybrid AlMg5/SiC/PLZT metal matrix composite produced by hot extrusion.  MATERIALS & DESIGN.  69:213-218. 2015
  • Microstructural development and mechanical properties of PM Ti-45Al-2Nb-2Mn-0.8vol.%TiB2 processed by field assisted hot pressing.  Journal of Materials Science & Technology.  30:1145-1154. 2014
  • Powder metallurgy CP-Ti performances: hydride-dehydride vs. sponge.  MATERIALS & DESIGN.  60:226-232. 2014
  • Study of the properties of low-cost powder metallurgy titanium alloys by 430 stainless steel addition.  MATERIALS & DESIGN.  60:628-636. 2014
  • Investigation of the factors influencing the tensile behaviour of PM Ti-3Al-2.5V alloy.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  609:266-272. 2014
  • Analysis of crystallographic slip and grain boundary sliding in a Ti-45Al-2Nb-2Mn (at%)-0.8 vol%TiB2 alloy by high temperature in situ mechanical testing.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  606:276-289. 2014
  • Microstructural and mechanical characterisation of 7075 aluminium alloy consolidated from a premixed powder by cold compaction and hot extrusion.  MATERIALS & DESIGN.  55:674-682. 2014
  • Flexural properties, thermal conductivity and electrical resistivity of prealloyed and master alloy addition powder metallurgy Ti-6Al-4V.  MATERIALS & DESIGN.  52:888-895. 2013
  • Influence of Sintering Parameters on the Properties of Powder Metallurgy Ti-3Al-2.5V Alloy.  MATERIALS CHARACTERIZATION.  84:48-57. 2013
  • Effect of stress level on the high temperature deformation and fracture mechanisms of Ti-45Al-2Nb-2Mn-0.8 vol. pct TiB2: an In Situ experimental study.  METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE.  44:1887-1896. 2013
  • Mechanical behaviour of pressed and sintered CP Ti and Ti-6Al-7Nb alloy obtained from master alloy addition powder.  Journal of the Mechanical Behavior of Biomedical Materials.  20:149-161. 2013
  • Influence of vacuum hot-pressing temperature on the microstructure and mechanical properties of Ti&-3Al&-2.5V alloy obtained by blended elemental and master alloy addition powders.  MATERIALS CHEMISTRY AND PHYSICS.  137:608-616. 2012
  • Mechanical behaviour of pressed and sintered titanium alloys obtained from master alloy addition powders.  Journal of the Mechanical Behavior of Biomedical Materials.  15:33-45. 2012
  • Mechanical behaviour of pressed and sintered titanium alloys obtained from prealloyed and blended elemental powders.  Journal of the Mechanical Behavior of Biomedical Materials.  14:29-38. 2012
  • Optimisation of mechanical milling process for production of AA 7075/(SiC or TiB2) composite powders.  POWDER METALLURGY.  55:280-286. 2012
  • Microstructural evolution and mechanical properties of the Ti-6Al-4V alloy produced by vacuum hot-pressing.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  546:189-197. 2012
  • Mechanical properties and microstructural evolution of vacuum hot-pressed titanium and Ti-6Al-7Nb alloy.  Journal of the Mechanical Behavior of Biomedical Materials.  9:91-99. 2012
  • In Situ Observations of the Deformation Behavior and Fracture Mechanisms of Ti-45Al-2Nb-2Mn+0.8 vol pct TiB2.  METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE.  43:1198-1208. 2012
  • Hot deformation behaviour and flow stress prediction of 7075 aluminium alloy powder compacts during compression at elevated temperatures.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  534:624-631. 2012
  • High resolution transmission electron microscopy study on the development of nanostructured precipitates in Al-Cu obtained by mechanical alloying.  MATERIALS CHEMISTRY AND PHYSICS.  132:125-130. 2012
  • Inductive hot-pressing of titanium and titanium alloy powders.  MATERIALS CHEMISTRY AND PHYSICS.  131:672-679. 2012
  • Estudio de los tratamientos térmicos de la aleación Ti-6Al-4V obtenida por pulvimetalurgia.  Trater Press.  36-44. 2011
  • Influence of powder characteristics on sintering behaviour and properties of PM Ti alloys produced from prealloyed powder and master alloy.  POWDER METALLURGY.  54:543-550. 2011
  • PM processing and characterisation of Ti-7Fe low cost titanium alloys.  POWDER METALLURGY.  54:242-252. 2011
  • Introducción al procesado pulvimetalúrgico del Ti=Introduction to podwer metallurgy processes for titanium manufacturing.  REVISTA DE METALURGIA.  47:169-188. 2011
  • Study of Compaction and Ejection of Hydrided-Dehydrided Titanium Powder.  METALS AND MATERIALS INTERNATIONAL.  17:45-55. 2011
  • Boride Coatings Obtained by Pack Cementation Deposited on Powder Metallurgy and Wrought Ti and Ti-6Al-4V.  SURFACE & COATINGS TECHNOLOGY.  205:2340-2347. 2010
  • Influence of Fe content and particle size the on the processing and mechanical properties of low-cost Ti&-xFe alloys.  MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING.  527:5664-5669. 2010
  • Aluminio pulvimetalúrgico: desarrollo y mejora de sus aleaciones y materiales compuestos = Aluminium PM: Alloys and Composites Development and Enhancement.  REVISTA DE METALURGIA.  44:206-215. 2008
  • Low-Cost Titanium Alloys? Iron May Hold the Answers.  Metal Powder Report.  63:24-27. 2008

• conference contributions 

  • Development and production of wires by powder metallurgical techniques for additive manufacturing.  46-47. 2022
  • Extrusion of metal powder to obtain wires of Aluminium-lithium for wire and arc additive manufacturing (WAAM) 2019
  • ProductionOf Wires Of Aluminium-lithium Alloys For WAAM By Extrusion Of Metal Powders 2019
  • Design of a learning method based on Flipped-Classroom methodologies using SPOCs in an engineering course.  407-413. 2017
  • Low-cost alfa+beta PM Ti alloys by Fe/Ni addition to pure Ti.  153-158. 2016
  • Electrochemical comparative study of corrosion behavior in physiological conditions of conventional and powder metallurgy titanium alloys 2015
  • Estudio electroquímico comparativo del comportamiento a corrosión en condiciones fisiológicas de aleaciones de titanio pulvimetalúrgicas y convencionales 2015
  • On the application of e-learning in engineering education 2015
  • Development of low-cost powder metallurgy Titanium Alloys by addition of commercial 430 stainless steel powder.  597-604. 2014
  • On the microstructure and properties of the Ti-3Al-2.5V alloy obtained by powder metallurgy.  121-128. 2014
  • Comparison of Microstructure and Properties of Ti-6Al-7Nb Alloy Processed by Different Powder Metallurgy Routes.  161-179. 2013
  • Magnetic non-contact harmonic drive.  2-5. 2013
  • Modification of a powder metallurgy gamma-TiAl alloy microstructure by heat treatments 2013
  • Processing of Elemental Titanium by Powder Metallurgy Techniques.  383-387. 2013
  • Analysis of the Temperature Effect on the Lamellar Microstructure Transformation of Gamma-TiAl Intermetallics Processed by Field Assisted Hot Pressing 2012
  • Analysis of the Temperature Effect on the Lamellar Microstructure Transformation of Gamma-TiAl Intermetallics Processed by Field Assisted Hot Pressing 2012
  • Compactación isostática en caliente del titanio y de la aleación Ti-6Al-7Nb: influencia de los parámetros de procesado en la microestructura y en las propiedades mecánicas 2012
  • In situ SEM Observations of the Tensile-Creep Deformation Behaviour and Fracture Mechanisms of a Gamma-TiAl Intermetallic Alloy at Low and High Stresses 2012
  • Influence of HIP Parameters on the Microstructure and Mechanical Properties of CP Ti and Ti-6Al-7NB Alloy.  17-22. 2012
  • Modificación de aleaciones de titanio pulvimetalúrgicas mediante compactación isostática en caliente 2012
  • Modification of Sintered Titanium alloys by Hot Isostatic Pressing.  63-69. 2012
  • PM Titanium: From Low Cost to High Performance 2012
  • An in-situ SEM evaluation of the elevated-temperature tensile and creep deformation behavior of Ti-45Al-2Mn-2Nb-XD 2011
  • Analysis of the temperature effect on the lamellar microstructure transformation of a Gamma-TiAl intermetalics processed by fiel assisted hot pressing 2011
  • Characterization of Al-Zn-Mg-Cu/(SiC or TiB2)p Composite Powders Obtained by Mechanical Milling 2011
  • Study of the Influence of the Sintering Tray on the Final Properties of PM Elemental Titanium.  289-294. 2011
  • Aleación biomética de titantio Ti-6Al-7Nb producida mediante técnicas pulvimetalúrgicas.  215-227. 2010
  • Biomedical Ti-6Al-7Nb Titanium Alloy Produced by P/M Techniques.  805-811. 2010
  • Boronizado de Ti y Ti-6Al-4V pulvimetalúrgicos y comparación con boronizado de sustratos Ti-6Al-4V convencionales.  241-250. 2010
  • Influence of Matrix Composition on the Sinterability and Properties of Fe-Based Cermets Reinforced with TiCN Particles.  457-464. 2010
  • Tin influence during on sintering of prealloyed and premixed Al-Cu powders.  289-296. 2010
  • Comparison of Boride Coatings Obtained by Pack Cementation on Powder Metallurgy and Wrought Ti and Ti-6Al-4V.  381-386. 2009
  • Influence of Titanium Powder Features on its Pressing Performance.  229-234. 2009
  • Ensayos de tracción en aleaciones de titanio pulvimetalúrgicas de bajo coste.  181-186. 2008
  • High Performance MMC's Obtained by Powder Metallurgy 2008
  • Obtención de aleaciones Ti-6Al-4V Pulvimetalúrgicas a partir de polvos prealeados y aleaciones maestras 2008
  • Propiedades mecánicas de aleaciones de Ti pulvimetalúrgicas de bajo coste.  151-154. 2008
  • Proyecto Leonardo: Desing for PM "Una experiencia de enseñanza a distancia en el area de materiales (Pulvimetalúrgia)" 2008
  • Response to Heat Treatments of Fe-TiCN Composites.  120-130. 2008
  • Sinterización y caracterización de aleaciones de Ti de bajo coste 2008
  • Study of Sinterting Aspects for the Manufacturing of Low-Cost Titanium Alloys.  161-175. 2008
  • Tin Addition Influence on the Optimization of an Al-Cu Alloy High Energy Milling and Liquid Phase Sintering.  118-128. 2008